At a glance
DIFFICULTYIntermediate
Access, condition, and tools can raise difficulty.
ESTIMATED TIMEVaries by access, underbody panels, and verification procedure
Confirm time from the exact procedure.
CONTENT SCOPEGeneral repair overview
Follow the exact vehicle procedure.
General steps; verify the exact vehicle procedure.
- 01ConfirmConfirm fault and exact vehicle fit
- 02SafetyReview hazards and stop limits first
- 03BudgetFull range · 30 currencies in Budget · not a quote
- 04Repair15 steps · prepare, remove, install
- 05Verify6 post-repair checks
Jump to a guide section
DIAGNOSE BEFORE DISASSEMBLY
An oil warning, leak, consumption complaint, engine noise, or contaminated oil needs diagnosis. Changing the oil is maintenance and may not correct the underlying fault.
Safety and stop conditions
Vehicle support warning
Vehicle support and hot-oil warning
Use rated support on a stable surface and verify the lift points. Hot oil and exhaust parts can cause burns; spilled oil can create fire and slip hazards.
Tools, parts, and information
TYPICAL TOOLSApproved lifting and support equipment if requiredDrain container with safe capacityCorrect drain-plug and filter toolsTorque wrench covering verified specificationsEye and hand protection
PARTS / EXACT INFORMATIONExact oil specification and quantityCorrect filter and required sealsDrain-plug, washer, housing, and underbody fastener instructionsLevel-check and maintenance-reset procedureResponsible used-oil recycling plan
Budget context
Source-backed repair estimate
U.S. national parts-and-labor estimate. Exact oil grade, capacity, access, and vehicle change the total; location, taxes, fees, and related repairs are excluded.
ECB rates compare currencies, not local service prices.
- 01USD band$160–$188 · per oil-change service
- 02Compare30 currencies · ECB rates dated 2026-10-05
- CAD CA$225–CA$270
- EUR €140–€170
Show all 30 currency values
- USD $160–$188
- CAD CA$225–CA$270
- EUR €140–€170
- GBP £120–£145
- AUD A$225–A$275
- JPY ¥25,315–¥29,750
- CHF 130–160
- NZD NZ$285–NZ$340
- INR ₹15,405–₹18,105
- MXN MX$2,900–MX$3,415
- CZK 3,490–4,105
- DKK 1,065–1,255
- HUF 52,520–61,720
- PLN 625–735
- RON 760–900
- SEK 1,605–1,890
- ISK 19,560–22,990
- NOK 1,535–1,810
- TRY 7,865–9,245
- BRL R$795–R$940
- CNY CN¥1,070–CN¥1,265
- HKD HK$1,255–HK$1,480
- IDR 2,866,100–3,367,675
- ILS ₪485–₪580
- KRW ₩215,035–₩252,670
- MYR 650–770
- PHP ₱10,025–₱11,785
- SGD 200–245
- THB 5,390–6,335
- ZAR 2,655–3,130
- 03VerifyConfirm vehicle and work scope
Price evidence · reviewed 2026-09-23
- Source 1: Oil Change Cost EstimateSource date 2026-09-03 · Retrieved 2026-09-23
Planning range only. Not a quote.
Preparation
5 steps
1
Verify oil specification, quantity, filter, seals, and every required fastener value
2
Confirm a stable work area and approved lift points
3
Warm only as the exact procedure directs, then shut down and allow safe handling
4
Remove access panels without mixing fasteners or damaging retainers
5
Position the drain container before loosening anything
Removal overview
5 steps
1
Open the fill point if directed and confirm it can be refitted
2
Remove the drain plug carefully while avoiding hot oil
3
Inspect the plug, threads, washer, drained oil, and evidence of leakage
4
Remove the filter using the correct tool and contain residual oil
5
Confirm old seals are removed from every sealing surface
Installation overview
5 steps
1
Install the specified new seals in the correct locations
2
Fit the drain plug and filter by the exact procedure and verified torque
3
Restore panels and fasteners correctly
4
Add less than the final expected amount using the specified oil
5
Follow the exact settle, temperature, and level-check procedure before final adjustment
Verification
6 checks
- Start only after tools and containers are clear
- Confirm oil-pressure indication behaves normally
- Inspect the filter and drain areas for leakage
- Shut down and recheck level by the specified method
- Reset maintenance information only after successful service
- Recheck for leakage after an appropriate drive and record the product used
Common mistakes
- Working under a vehicle supported only by a jackA jack is a lifting device, not safe working support.
- Double-gasketing the filterAn old seal left behind can cause rapid oil loss.
- Guessing capacity or torqueOverfill, underfill, stripped threads, or a loose component can result.
- Resetting the reminder before completing the workThe record should reflect a verified service.
Exact-information boundary
DO NOT GUESS OR TRANSFER VALUESOil chemistry and viscosity, quantity, filter, drain hardware, torque, level conditions, interval, and reset procedure must come from current information for the exact engine.
Verify the correct information using current manufacturer service documentation for the VIN, engine, trim, transmission, drivetrain, market, and installed equipment.