At a glance
DIFFICULTYAdvanced
Access, condition, and tools can raise difficulty.
ESTIMATED TIMEVaries widely with access and vehicle design
Confirm time from the exact procedure.
CONTENT SCOPEGeneral repair overview
Follow the exact vehicle procedure.
General steps; verify the exact vehicle procedure.
- 01ConfirmConfirm fault and exact vehicle fit
- 02SafetyReview hazards and stop limits first
- 03BudgetFull range · 30 currencies in Budget · not a quote
- 04Repair12 steps · prepare, remove, install
- 05Verify4 post-repair checks
Jump to a guide section
DIAGNOSE BEFORE DISASSEMBLY
A click or no-crank condition does not prove the starter failed. Confirm battery condition, cable voltage loss, start command, interlocks, grounds, and that the engine can rotate before replacement.
Safety and stop conditions
Vehicle support warning
High-current and vehicle-support warning
Starter wiring can carry very high current. Isolate it exactly as the vehicle procedure requires; if access is underneath, use approved lift/support equipment and never rely on a jack alone.
Tools, parts, and information
TYPICAL TOOLSEye protection and insulated hand tools where specifiedBattery and circuit test equipmentCorrect hand tools for the exact fastenersApproved lift and vehicle-support equipment if access requires working underneath
PARTS / EXACT INFORMATIONStarter application matched to the exact engine and transmissionCurrent vehicle power-down and starter-circuit procedureVerified cable routing, fastener specifications, and any shims or bracketsRequired relearn, initialization, or post-repair checks
Budget context
Source-backed repair estimate
U.S. national parts-and-labor estimate. Test the starting circuit before replacing a starter. Vehicle, access, location, taxes, fees, and related repairs can change the total.
ECB rates compare currencies, not local service prices.
- 01USD band$565–$796 · per replacement estimate
- 02Compare30 currencies · ECB rates dated 2026-10-05
- CAD CA$805–CA$1,135
- EUR €500–€715
Show all 30 currency values
- USD $565–$796
- CAD CA$805–CA$1,135
- EUR €500–€715
- GBP £425–£605
- AUD A$810–A$1,145
- JPY ¥89,395–¥125,955
- CHF 465–665
- NZD NZ$1,010–NZ$1,425
- INR ₹54,405–₹76,655
- MXN MX$10,250–MX$14,450
- CZK 12,330–17,380
- DKK 3,765–5,315
- HUF 185,475–261,310
- PLN 2,205–3,115
- RON 2,690–3,795
- SEK 5,670–7,995
- ISK 69,085–97,335
- NOK 5,420–7,645
- TRY 27,770–39,130
- BRL R$2,815–R$3,970
- CNY CN¥3,785–CN¥5,340
- HKD HK$4,430–HK$6,250
- IDR 10,120,925–14,258,870
- ILS ₪1,730–₪2,440
- KRW ₩759,350–₩1,069,815
- MYR 2,305–3,255
- PHP ₱35,410–₱49,890
- SGD 720–1,020
- THB 19,035–26,825
- ZAR 9,390–13,235
- 03VerifyConfirm vehicle and work scope
Price evidence · reviewed 2026-10-05
- Source 1: Starter Replacement Cost EstimateSource date 2026-09-03 · Retrieved 2026-10-05
Planning range only. Not a quote.
Preparation
4 steps
1
Capture the original no-crank behavior and complete circuit diagnosis
2
Read the exact replacement procedure, including battery isolation and retained-power precautions
3
Secure the vehicle; use approved support equipment if access is underneath
4
Locate the starter, cable routing, control connector, shields, and any one-time-use hardware
Removal overview
4 steps
1
Follow the exact power-down and battery-disconnection sequence
2
Remove only the access parts identified by the procedure and preserve routing
3
Verify the high-current circuit is isolated before touching starter terminals
4
Support the starter, remove its connections and fasteners in the specified order, and inspect for heat, corrosion, or damage
Installation overview
4 steps
1
Compare the replacement's application, terminals, mounting face, and included hardware
2
Fit any specified shims, brackets, shields, and fasteners in their recorded positions
3
Reconnect power and control wiring by the exact procedure and tighten only to verified specifications
4
Restore removed parts and confirm cables cannot contact moving or hot components
Verification
4 checks
- Check that tools and loose hardware are clear before restoring power
- Confirm connectors, cable covers, shields, and supports are restored
- Repeat the original start conditions and listen for abnormal engagement or noise
- Scan for relevant faults and continue diagnosis if the original complaint remains
Common mistakes
- Replacing the motor after a single clickLow battery capacity, cable loss, a control fault, an interlock, or a mechanically restricted engine can produce similar symptoms.
- Touching the high-current terminal before isolationA tool can short battery current to the vehicle structure and cause burns, fire, or severe damage.
- Guessing access or fastener specificationsStarter location, support needs, brackets, wiring, and tightening procedures vary by vehicle.
Exact-information boundary
DO NOT GUESS OR TRANSFER VALUESStarter application, battery-isolation sequence, lifting points, wiring arrangement, shims, fastener torque, initialization, and verification must be confirmed for the exact vehicle. This overview supplies no vehicle-specific values.
Verify the correct information using current manufacturer service documentation for the VIN, engine, trim, transmission, drivetrain, market, and installed equipment.